Advertisement
Message Forums |
|
 Topic: Reich move control, "mk1"? -cross activat
|
  |
| Discounted Insurance Quotes for UKCampsite.co.uk visitors! Up to 12.5% off! |
|
|
|
23/2/2011 at 8:48pm
Location:
Outfit:
View Profile
Reply
Quote
|
Joined: 16/7/2007 Platinum Member 
Forum Posts: 730
| Site Reviews Total: | 1 |
|
| Site Reviews 2024: | 0  |
| Site Reviews 2023: | 0 |
| Site Reviews 2022: | 0 |
| Site Reviews 2021: | 0 |
| Site Reviews 2020: | 0 |
| Site Reviews 2019: | 0 |
| Site Reviews 2018: | 0 |
|
| Site Nights 2024: | 0 |
| Site Nights 2023: | 0 |
| Site Nights 2022: | 0 |
| Site Nights 2021: | 0 |
| Site Nights 2020: | 0 |
| Site Nights 2019: | 0 |
| Site Nights 2018: | 0 |
|
Quote: Originally posted by David Klyne on 23/2/2011
I am sure if you e-mail Reich UK with the serial number tey would be able to advise. Just a thought, we have a cross activator on our Powertouch and its quite stiff to engage. My previous Reich Move Control was easy to engage one wheel at a time.
David
Hi David,
Our Reich has a manual cross actuator - ie it winds on both rollers from either side, and is fairly easy to wind on all the way - not much harder than winding a steady down anyway. The rollers are the ridged type not the gritty type.
Shirley.
|
24/2/2011 at 1:14am
Location: Lanarkshire
Outfit: Compass Lynx 340 2
View Profile
Reply
Quote
|
Joined: 26/5/2005 Diamond Member 
Forum Posts: 1549
| Site Reviews Total: | 3 |
|
| Site Reviews 2024: | 0 |
| Site Reviews 2023: | 0 |
| Site Reviews 2022: | 0 |
| Site Reviews 2021: | 0 |
| Site Reviews 2020: | 0 |
| Site Reviews 2019: | 0 |
| Site Reviews 2018: | 0 |
|
| Site Nights 2024: | 0 |
| Site Nights 2023: | 0 |
| Site Nights 2022: | 0 |
| Site Nights 2021: | 0 |
| Site Nights 2020: | 0 |
| Site Nights 2019: | 0 |
| Site Nights 2018: | 0 |
|
Hi jackrussel, Welcome to the forum, I have the Reich mover, If yours has a small square bar (should have small hole drilled through it to take nut/bolt) protruding from rear of the winding nut, then it will take an actuator bar, you can make your own, with 2 lenghts of metal tubes, one to slide inside other (round or square ), make sure they overlap a few inches in center, drill one hole end of each bar, the same diameter as hole on mover bar, temperarly fit actuation bar to mover, put pin in each end of mover for correct alignment, mark the actuator bar horizontaly and verticaly where they overlap,dismantel and re align the bars to marks made, drill through the two bars, refit and bolt, You can also get new aluminum rollers to fit your mover when needed. Hope this has been of help.
-------------
If everything runs smoothly then I must have done something wrong
If in Doubt Check it Out.
John
|
|
|
5502 Visitors online !
Free UKCampsite.co.uk Window Sticker - Recommend to Friend - Add a Missing Campsite
[Message Forums]
[Caravan Sites & Camping]
[Company Listings]
[Features / Advice]
[Virtual Brochure]
[Shop!]
[Reception]
[Competitions]
[Caravans & Motorhomes For Sale]
[Event Diary]
[Contact Us]
[Tent Reviews]
Please note we are not responsible for the content of external sites & any reviews represent the author's personal view only. Please report any error here. You may view our privacy and cookie policy and terms and conditions here. All copyrights & other intellectual property rights in the design and content of this web site are reserved to the UKCampsite.co.uk © 1999 - 2024 |
Advertisement
|
|
|
