Advertisement
Message Forums |
|
 Topic: Floor Delamination More Info
|
  |
| Discounted Insurance Quotes for UKCampsite.co.uk visitors! Up to 12.5% off! |
|
|
|
03/11/2011 at 3:16pm
Location: Lancashire
Outfit: Caravan now Sold
View Profile
Reply
Quote
|
Joined: 30/6/2002 Diamond Member 
Forum Posts: 23517
| Site Reviews Total: | 1 |
|
| Site Reviews 2024: | 0  |
| Site Reviews 2023: | 0 |
| Site Reviews 2022: | 0 |
| Site Reviews 2021: | 0 |
| Site Reviews 2020: | 0 |
| Site Reviews 2019: | 0 |
| Site Reviews 2018: | 0 |
|
| Site Nights 2024: | 0 |
| Site Nights 2023: | 0 |
| Site Nights 2022: | 0 |
| Site Nights 2021: | 0 |
| Site Nights 2020: | 0 |
| Site Nights 2019: | 0 |
| Site Nights 2018: | 0 |
|
hi this is my version,hope it helps,hi,delamination...frightening no if you set out your stall and take your time.this is not a two hour job as stated,when you have finished you will know why they charge so much at the caravan repair shop.i have just done ours a few months ago.i will go through the steps best i can.ours had gone in two places,next to the door entrance and next to the sink four feet away.you will find that delamination is where the floor is used most.ie next to the sink and the door entrance.first decide how much delamination you have,ie.2 feet (old school) or 6 feet,this information is required when you go to order your epoxi resin mix.one mix will cover about 3 feet by 3 feet.got mine from barrons £25 for both tins.you also need a large syringe to inject the mixed epoxi resin.this will also sell.also the chemicals (glue) are called apollo 1 and apollo 2.i think the code is A8136.the small tin is the hardener and must be used in the time on the tin.the first thing is to remove all carpets or lino.second(must) tape up all joints and the cowls under the caravan .use a good tape.ie brown packing tape,3 in wide.if you dont the glue will run out on to the ground outside through all the seams.you will not know until you see a pool on the path..third ,support the floor under the van in some way so it cannnot bend when pressure is placed on top,do not push up the floor.you can damage the fittings inside.use wood blocks stacked up just touching the floor on the underside in the same place as the delamination.fourth find a sharp 10mm drill .you need to buy 10 mm round wood to cut and plug the holes,sold in 6 foot lengths.this needs cutting into plugs,half inch long and sanded down at one end to make it go in easy.the next step is to do a test hole,find a place that has no gas pipes on the underside.slowly drill one hole until it only just touches the plywood at the bottom.DO NOT DRILL THROUGH.tape up the drill at this depth,use plenty of tape to stop the drill going deeper than it should.mark out the area of delamination,black marker,in a square grid pattern of 4 inch each way .when finished you will have a large square full of holes to the size of the delamination.ie.3 x 3 feet.clean away all and any dust or shavings.have a large polythene bag ready to put over the square,the glue does not stick to polythene.you need a tin or old pan to mix into of the correct size for size of mix.a clean strong stick to stir the mix.only mix what you need within the time allowed.start at the rear end injecting the holes one by one until it flows out then plug with the wood plug.when finished ,place poly bag over all holes.put a heavy weight on top ie.wheels and tyres or gas bottles.leave for 24 hours to dry.sand down all plugs until smooth.you must wear a mask for the fumes and open the windows when you are doing the job.rubber gloves are handy too.CHECK UNDERSIDE FOR GAS PIPES BEFORE STARTING.wish i could type.![[:o)]](https://www.ukcampsite.co.uk/chatter/forum_images/smiley20.gif)
-------------
the only silly question is the one you do not ask.
|
|
|
5057 Visitors online !
Free UKCampsite.co.uk Window Sticker - Recommend to Friend - Add a Missing Campsite
[Message Forums]
[Caravan Sites & Camping]
[Company Listings]
[Features / Advice]
[Virtual Brochure]
[Shop!]
[Reception]
[Competitions]
[Caravans & Motorhomes For Sale]
[Event Diary]
[Contact Us]
[Tent Reviews]
Please note we are not responsible for the content of external sites & any reviews represent the author's personal view only. Please report any error here. You may view our privacy and cookie policy and terms and conditions here. All copyrights & other intellectual property rights in the design and content of this web site are reserved to the UKCampsite.co.uk © 1999 - 2024 |
Advertisement
|
|
|
I have been told that after Drilling the Holes for injecting the Hardener into the Floor..It is best to get an old piece of wire coat hanger etc,put a bend in the end of the wire and use it to stick just inside of each Hole, and jiggle it around to Break up the old flooring..Is this a good idea.Or would it cause problems..Its said that it is suppose to let the Hardener spread more evenly..Anybody done this..
I remember year's ago when I tried to reposition a hanging wall cupboard in the kitchen. Ended up by drilling through to the dining room - you could see right through. No chance I'd risk anything like that. I'd personally leave it to those that can!! Wife doesn't even like my winding up the corner steadies with the rechargeable drill (and bit). 
